3 files changed, 125 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/hwmon/ads1015.txt b/Documentation/devicetree/bindings/hwmon/ads1015.txt
new file mode 100644
index 000000000..918a507d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ads1015.txt
@@ -0,0 +1,73 @@
+ADS1015 (I2C)
+
+This device is a 12-bit A-D converter with 4 inputs.
+
+The inputs can be used single ended or in certain differential combinations.
+
+For configuration all possible combinations are mapped to 8 channels:
+  0: Voltage over AIN0 and AIN1.
+  1: Voltage over AIN0 and AIN3.
+  2: Voltage over AIN1 and AIN3.
+  3: Voltage over AIN2 and AIN3.
+  4: Voltage over AIN0 and GND.
+  5: Voltage over AIN1 and GND.
+  6: Voltage over AIN2 and GND.
+  7: Voltage over AIN3 and GND.
+
+Each channel can be configured individually:
+ - pga is the programmable gain amplifier (values are full scale)
+    0: +/- 6.144 V
+    1: +/- 4.096 V
+    2: +/- 2.048 V (default)
+    3: +/- 1.024 V
+    4: +/- 0.512 V
+    5: +/- 0.256 V
+ - data_rate in samples per second
+    0: 128
+    1: 250
+    2: 490
+    3: 920
+    4: 1600 (default)
+    5: 2400
+    6: 3300
+
+1) The /ads1015 node
+
+  Required properties:
+
+   - compatible : must be "ti,ads1015"
+   - reg : I2C bus address of the device
+   - #address-cells : must be <1>
+   - #size-cells : must be <0>
+
+  The node contains child nodes for each channel that the platform uses.
+
+  Example ADS1015 node:
+
+    ads1015@49 {
+	    compatible = "ti,ads1015";
+	    reg = <0x49>;
+	    #address-cells = <1>;
+	    #size-cells = <0>;
+
+	    [ child node definitions... ]
+    }
+
+2) channel nodes
+
+  Required properties:
+
+   - reg : the channel number
+
+  Optional properties:
+
+   - ti,gain : the programmable gain amplifier setting
+   - ti,datarate : the converter data rate
+
+  Example ADS1015 channel node:
+
+    channel@4 {
+	    reg = <4>;
+	    ti,gain = <3>;
+	    ti,datarate = <5>;
+    };
diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt
new file mode 100644
index 000000000..c6f66674f
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt
@@ -0,0 +1,29 @@
+NTC Thermistor hwmon sensors
+-------------------------------
+
+Requires node properties:
+- "compatible" value : one of
+	"ntc,ncp15wb473"
+	"ntc,ncp18wb473"
+	"ntc,ncp21wb473"
+	"ntc,ncp03wb473"
+	"ntc,ncp15wl333"
+- "pullup-uv"	Pull up voltage in micro volts
+- "pullup-ohm"	Pull up resistor value in ohms
+- "pulldown-ohm" Pull down resistor value in ohms
+- "connected-positive" Always ON, If not specified.
+		Status change is possible.
+- "io-channels"	Channel node of ADC to be used for
+		conversion.
+
+Read more about iio bindings at
+	Documentation/devicetree/bindings/iio/iio-bindings.txt
+
+Example:
+	ncp15wb473@0 {
+		compatible = "ntc,ncp15wb473";
+		pullup-uv = <1800000>;
+		pullup-ohm = <47000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc 3>;
+	};
diff --git a/Documentation/devicetree/bindings/hwmon/vexpress.txt b/Documentation/devicetree/bindings/hwmon/vexpress.txt
new file mode 100644
index 000000000..9c27ed694
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/vexpress.txt
@@ -0,0 +1,23 @@
+Versatile Express hwmon sensors
+-------------------------------
+
+Requires node properties:
+- "compatible" value : one of
+	"arm,vexpress-volt"
+	"arm,vexpress-amp"
+	"arm,vexpress-temp"
+	"arm,vexpress-power"
+	"arm,vexpress-energy"
+- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg
+  (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt
+  for more details)
+
+Optional node properties:
+- label : string describing the monitored value
+
+Example:
+	energy@0 {
+		compatible = "arm,vexpress-energy";
+		arm,vexpress-sysreg,func = <13 0>;
+		label = "A15 Jcore";
+	};